Q1Driving safely
What two things does the handbook say will help you prevent a rollover?
- ALoad the heaviest cargo on top and keep a steady speed in turns
- BKeep the cargo as low as possible and drive slowly around turns
- CKeep the tires at maximum pressure and use the trailer hand valve in curves
- DDrive in the left lane and brake hard in the middle of turns
Show answerHide answer
Answer B Keep the cargo as low as possible and drive slowly around turns
A higher center of gravity makes a truck easier to tip over, and rollovers happen when you take turns too fast. Low cargo and slow turns attack both causes.
Texas CDL Handbook §6.1.1
Q2Driving safely
You make a sudden lane change while pulling double trailers. Which part of the rig is most likely to turn over?
- AThe tractor
- BThe rear trailer
- CThe front trailer
- DAll units are equally likely to turn over
Show answerHide answer
Answer B The rear trailer
Rearward amplification causes a crack-the-whip effect, so a quick steering move is magnified as it passes back through the rig. The last trailer gets the biggest swing.
Texas CDL Handbook §6.1.2
Q3Driving safely
Compared with the same rig fully loaded, how does an empty large combination vehicle stop?
- AIt takes longer to stop
- BIt stops in about half the distance
- CIt stops in exactly the same distance
- DIt cannot lock its wheels
Show answerHide answer
Answer A It takes longer to stop
When lightly loaded, stiff suspension springs and strong brakes give poor traction, so the wheels lock up easily. That makes stopping take longer, not shorter.
Texas CDL Handbook §6.1.3
Q4Driving safely
When backing a tractor-trailer, which way do you turn the steering wheel to start the trailer turning?
- AThe same direction you want the trailer to go
- BOpposite to the direction you want the trailer to go
- CAlways to the right
- DYou do not steer; you only use the mirrors
Show answerHide answer
Answer B Opposite to the direction you want the trailer to go
Backing a trailer works the reverse of backing a car. Once the trailer starts to turn, you turn the wheel back the other way to follow it.
Texas CDL Handbook §6.1.7
Q5Trailer air brakes
What should the trailer hand valve (trolley valve) be used for?
- ASlowing down on long downgrades
- BStraightening out a trailer skid
- COnly to test the trailer brakes
- DHolding the trailer when parked
Show answerHide answer
Answer C Only to test the trailer brakes
Using the hand valve while driving can make the trailer skid. The foot brake sends air to all the brakes on the rig, which is much less likely to cause a skid or jackknife.
Texas CDL Handbook §6.2.1
Q6Trailer air brakes
What is the job of the tractor protection valve?
- ASend extra air to the trailer when the tractor's pressure is low
- BKeep the trailer's ABS powered when the engine is off
- CKeep air in the tractor's brake system if the trailer breaks away or has a bad leak
- DRelease the trailer's brakes automatically if air pressure drops
Show answerHide answer
Answer C Keep air in the tractor's brake system if the trailer breaks away or has a bad leak
If the trailer breaks loose or develops a bad leak, the valve stops air from leaving the tractor, so the tractor keeps the air it needs for its own brakes.
Texas CDL Handbook §6.2.2
Q7Trailer air brakes
What two jobs does the emergency (supply) air line do?
- AIt carries the brake-light signal and powers the trailer ABS
- BIt controls the service brakes and inflates the trailer tires
- CIt fills the trailer air tanks and controls the trailer emergency brakes
- DIt drains moisture from the tanks and raises the landing gear
Show answerHide answer
Answer C It fills the trailer air tanks and controls the trailer emergency brakes
The emergency line supplies air to the trailer tanks. If it loses pressure, for example when the trailer breaks loose, the trailer emergency brakes come on.
Texas CDL Handbook §6.2.4
Q8Trailer air brakes
You push in the trailer air supply control, but the trailer spring brakes do not release. What should you check?
- AThe trailer ABS malfunction lamp on the left side
- BThe fifth wheel locking lever and safety latch
- CThe trailer electrical cord and its safety catch
- DThe air-line connections; the lines may be crossed
Show answerHide answer
Answer D The air-line connections; the lines may be crossed
If the lines are crossed, supply air goes into the service line instead of charging the trailer tanks, so there is no air to release the spring brakes.
Texas CDL Handbook §6.2.5
Q9Trailer air brakes
On a set of doubles, which air-line shut-off valves (cut-out cocks) should be closed?
- AAll of them, until the brakes are tested
- BThe ones at the back of the first trailer
- COnly the ones at the back of the last trailer
- DThe ones on the converter dolly
Show answerHide answer
Answer C Only the ones at the back of the last trailer
All other shut-off valves must be open so air reaches every trailer. Only the valves at the very back are closed, because nothing is being towed behind them.
Texas CDL Handbook §6.2.7
Q10Antilock brakes
Trailers and converter dollies built on or after what date are required to have antilock brakes (ABS)?
- AMarch 1, 1988
- BMarch 1, 1995
- CMarch 1, 1998
- DMarch 1, 2005
Show answerHide answer
Answer C March 1, 1998
All trailers and converter dollies built on or after March 1, 1998 must have ABS. Many older ones were equipped with it voluntarily.
Texas CDL Handbook §6.3.1
Q11Antilock brakes
Where will you find a trailer's ABS malfunction lamp?
- AA red lamp in the center of the rear bumper
- BA blue lamp on the right side near the landing gear
- CA green lamp on top of the trailer nose
- DA yellow lamp on the left side, at the front or rear corner
Show answerHide answer
Answer D A yellow lamp on the left side, at the front or rear corner
Trailers built on or after March 1, 1998 have a yellow ABS malfunction lamp on the left side, at the front or rear corner; older trailers may not have one. Dollies built on or after that date must also have a lamp on the left side.
Texas CDL Handbook §6.3.1
Q12Antilock brakes
On an older trailer, how can you tell if it has ABS?
- ACheck whether the trailer has spring brakes
- BCount the air tanks under the trailer
- CPump the brakes and listen for a buzzer in the cab
- DLook underneath for an ECU and wheel speed sensor wires
Show answerHide answer
Answer D Look underneath for an ECU and wheel speed sensor wires
Units built before the ABS requirement may not have the lamp, so the handbook says to look for the electronic control unit and wheel speed sensor wiring.
Texas CDL Handbook §6.3.1
Q13Coupling
Before coupling, what position should the fifth wheel be in?
- ATilted up toward the cab, with the jaws closed
- BLevel, with the jaws closed and locked
- CTilted down toward the rear of the tractor, with the jaws open
- DTilted down toward the rear, with the jaws closed
Show answerHide answer
Answer C Tilted down toward the rear of the tractor, with the jaws open
The fifth wheel should tilt down toward the rear with the jaws open and the safety unlocking handle in the automatic lock position, ready to receive the kingpin.
Texas CDL Handbook §6.4.1
Q14Coupling
After the kingpin locks into the fifth wheel, how do you test that the trailer is locked onto the tractor?
- ARelease the trailer brakes and drive forward quickly to see if the trailer follows
- BRaise the landing gear slightly and pull gently against the locked trailer brakes
- CRaise the landing gear all the way, then back up hard against the trailer
- DWatch the air pressure gauge for a drop while the engine idles
Show answerHide answer
Answer B Raise the landing gear slightly and pull gently against the locked trailer brakes
Pulling gently against the locked trailer brakes shows whether the fifth wheel is holding the kingpin before you rely on it.
Texas CDL Handbook §6.4.1
Q15Coupling
When you inspect the coupling, you see a gap between the upper and lower fifth wheel. What does this mean?
- AIt is normal; the gap leaves room for the rig to turn
- BThe fifth wheel plate needs more grease before you go
- CSomething is wrong; the kingpin may be on top of the jaws
- DThe trailer is too low and should be cranked higher
Show answerHide answer
Answer C Something is wrong; the kingpin may be on top of the jaws
There should be no space between the upper and lower fifth wheel. A gap can mean the kingpin is sitting on top of closed jaws, and the trailer could come loose very easily.
Texas CDL Handbook §6.4.1
Q16Coupling
After coupling, how far should you raise the landing gear before driving?
- AJust until the pads clear the pavement
- BAbout halfway up
- CLeave it down an inch for support
- DAll the way up
Show answerHide answer
Answer D All the way up
Landing gear left only part way up can catch on railroad tracks or other objects. After raising it, secure the crank handle.
Texas CDL Handbook §6.4.1
Q17Uncoupling
When uncoupling, why do you back up gently against the kingpin after locking the trailer brakes?
- ATo test the trailer emergency brakes
- BTo lift the trailer off the fifth wheel
- CTo ease pressure on the locking jaws
- DTo bleed air from the trailer tanks
Show answerHide answer
Answer C To ease pressure on the locking jaws
Setting the parking brakes while the tractor pushes against the kingpin holds the rig with the pressure off the jaws.
Texas CDL Handbook §6.4.2
Q18Uncoupling
When should you chock the trailer wheels during uncoupling?
- AIf it has no spring brakes, or you are not sure
- BOnly if you are parking on a hill or slope
- COnly when the trailer is loaded with cargo
- DNever; the trailer emergency brakes always hold
Show answerHide answer
Answer A If it has no spring brakes, or you are not sure
Air can leak out of the trailer tank and release its emergency brakes. Without chocks, the trailer could roll.
Texas CDL Handbook §6.4.2
Q19Uncoupling
When you first pull the tractor forward to uncouple, where should you stop?
- AWith the tractor completely clear of the trailer
- BWith the fifth wheel still under the kingpin
- CRight after the air lines pull loose
- DWith the tractor frame still under the trailer
Show answerHide answer
Answer D With the tractor frame still under the trailer
Leaving the frame under the trailer keeps it from falling to the ground if the landing gear collapses or sinks. Secure the tractor and check the supports before pulling clear.
Texas CDL Handbook §6.4.2
Q20Inspection
What should you look for when inspecting the air lines between the tractor and trailer?
- APulled tight so they cannot move at all
- BTied to the exhaust stack to stay warm
- CLeft loose and lying on the catwalk deck
- DNo leaks, secured, with enough slack for turns
Show answerHide answer
Answer D No leaks, secured, with enough slack for turns
Air lines should be properly connected to the glad hands, free of leaks and damage, and secured with enough slack for turns.
Texas CDL Handbook §6.5.1
Q21Inspection
How do you check that air is reaching all the trailers?
- AWatch the yellow trailer ABS lamp for a flash when you press the brake pedal
- BPump the foot brake with the engine off until the air supply knob pops out
- CDrain the tractor's air tanks and check how much water comes out
- DOpen the emergency line valve at the rear of the last trailer and listen for air
Show answerHide answer
Answer D Open the emergency line valve at the rear of the last trailer and listen for air
Hearing air escape at the rear shows the system is charged all the way back. Close that valve, then repeat with the service line while the trailer hand brake or brake pedal is applied.
Texas CDL Handbook §6.5.2
Q22Inspection
How do you test the tractor protection valve?
- APull the tractor forward against the locked trailer brakes in a low gear
- BOpen the shut-off valve at the back of the last trailer and listen for air
- CApply the trailer hand valve while moving slowly and feel for braking
- DEngine off, pump the brake pedal to lower air pressure and watch the knob pop out
Show answerHide answer
Answer D Engine off, pump the brake pedal to lower air pressure and watch the knob pop out
First charge the trailer air system. As pressure falls into the range the manufacturer specifies (usually 20 to 45 psi), the control should pop out or move to 'emergency'. If it doesn't, a trailer leak could drain the tractor's air.
Texas CDL Handbook §6.5.2
Q23Federal rules
Under federal rules, a truck tractor with air brakes that tows air-braked trailers must have how many ways to activate the trailer emergency brakes?
- AOne: an automatic system that works on low air pressure
- BTwo: one automatic and one manual control at the driver's seat
- COne: a manual control mounted on the front of the trailer
- DThree: one manual control for each axle of the trailer
Show answerHide answer
Answer B Two: one automatic and one manual control at the driver's seat
393.43(b) requires an automatic means that works when tractor air drops to a set point between 20 and 45 psi, plus a manual control the seated driver can operate. The manual control may not be set up to block the automatic one.
49 CFR 393.43
Q24Federal rules
Federal rules require air-braked trailers to use no-bleed-back relay emergency valves (or the equivalent). What do these protect?
- AThe tractor's air dryer, from trailer moisture
- BThe trailer's supply reservoir, from air flowing back to the tractor
- CThe glad hand seals, from dirt and water
- DThe trailer ABS, from a low-voltage power supply
Show answerHide answer
Answer B The trailer's supply reservoir, from air flowing back to the tractor
393.43(e) requires these valves so that if the towing vehicle's air pressure drops, the trailer's supply reservoir does not lose its air back to the towing vehicle. That keeps air on the trailer for its brakes.
49 CFR 393.43
Q25Federal rules
To pull double or triple trailers, a CDL holder needs an endorsement. What test does federal law require for it?
- AA knowledge test
- BA knowledge test and a skills test
- CA skills test only
- DNo test; the endorsement is automatic with a Class A CDL
Show answerHide answer
Answer A A knowledge test
383.93(b) and (c) list the double/triple trailers endorsement and require only a knowledge test for it.
49 CFR 383.93