Q1System parts
Air brakes are really made up of three braking systems. Which three?
- APrimary, secondary and trailer
- BService, parking and emergency
- CFront, rear and trailer
- DFoot, hand and engine
Show answerHide answer
Answer B Service, parking and emergency
The service system works with the brake pedal in normal driving, and the parking system works with the parking brake control. The emergency system uses parts of both to stop the vehicle if the brake system fails.
Texas CDL Handbook §5
Q2System parts
The safety relief valve in the first air tank is usually set to open at about what pressure?
- A100 psi
- B125 psi
- C150 psi
- D200 psi
Show answerHide answer
Answer C 150 psi
This valve guards against over-pressure in the tanks and lines, and it normally opens at 150 psi. If it ever releases air, have a mechanic find the fault.
Texas CDL Handbook §5.1.6
Q3System parts
Why should you avoid pressing and releasing the brake pedal when you don't need to?
- AIt can let air out faster than the compressor can replace it
- BIt makes the governor stop the compressor
- CIt overfills the tanks and opens the safety valve
- DIt drains water out of the air tanks
Show answerHide answer
Answer A It can let air out faster than the compressor can replace it
Each time you release the brakes, some compressed air leaves the system. If pressure gets too low, the brakes won't work.
Texas CDL Handbook §5.1.7
Q4Dual air systems
What is a dual air brake system?
- AOne air system with two compressors feeding the same tank
- BTwo separate air brake systems that share one set of brake controls
- CAn air system backed up by a hydraulic system
- DSeparate brake pedals for the tractor and the trailer
Show answerHide answer
Answer B Two separate air brake systems that share one set of brake controls
Each of the two systems has its own tanks, hoses and lines, but the driver uses a single set of controls. Most heavy-duty vehicles use dual systems for safety.
Texas CDL Handbook §5.2
Q5Dual air systems
Before driving a vehicle with a dual air system, let the compressor build at least how much pressure in both systems?
- A55 psi
- B80 psi
- C100 psi
- D150 psi
Show answerHide answer
Answer C 100 psi
Wait until both the primary and secondary systems have at least 100 psi. Watch both gauges (or both needles) while it builds.
Texas CDL Handbook §5.2
Q6Dual air systems
While driving a vehicle with dual air brakes, one of the two systems gets very low on air. What happens?
- AEither the front or the rear brakes won't work fully, so it takes longer to stop
- BNothing changes, because the other system works all the brakes
- CThe governor shuts off the compressor
- DThe brakes on every wheel lock up at once
Show answerHide answer
Answer A Either the front or the rear brakes won't work fully, so it takes longer to stop
Each system works only part of the brakes, so losing one leaves some brakes not fully working. Bring the vehicle to a safe stop and have the system fixed.
Texas CDL Handbook §5.2
Q7Spring brakes & parking
While you are driving, what holds back the powerful springs in the spring brakes?
- AHydraulic fluid
- BAir pressure
- CAn electric solenoid
- DThe slack adjusters
Show answerHide answer
Answer B Air pressure
Air pressure keeps the springs from applying the brakes. If the air is removed, by the parking control or by a leak, the springs put the brakes on.
Texas CDL Handbook §5.1.14
Q8Spring brakes & parking
Tractor and straight truck spring brakes come fully on when air pressure drops to what range?
- A20 to 45 psi
- B55 to 75 psi
- C80 to 85 psi
- D100 to 125 psi
Show answerHide answer
Answer A 20 to 45 psi
They come fully on somewhere between 20 and 45 psi, typically 20 to 30 psi. Don't wait for this: stop safely as soon as the low-air warning comes on.
Texas CDL Handbook §5.1.14
Q9Spring brakes & parking
On newer vehicles with air brakes, what does the parking brake control look like, and how do you set it?
- AA yellow, diamond-shaped knob that you push in to apply
- BA yellow, diamond-shaped knob that you pull out to apply
- CA red, eight-sided button that you push in to apply
- DA lever on the steering column that you lift to apply
Show answerHide answer
Answer B A yellow, diamond-shaped knob that you pull out to apply
Pull the yellow diamond knob out to put the spring brakes on, and push it in to release them. Older vehicles may use a lever instead.
Texas CDL Handbook §5.1.15
Q10Spring brakes & parking
You have just come down a long, steep grade and your brakes are very hot. How should you park?
- ASet the parking brakes right away and hold the brake pedal down firmly
- BSet the parking brakes, then fan the brake pedal to help cool them
- CSkip the parking brakes; chock the wheels on level ground and let the brakes cool
- DLeave it in neutral without parking brakes or wheel chocks
Show answerHide answer
Answer C Skip the parking brakes; chock the wheels on level ground and let the brakes cool
Very hot brakes can be damaged if you set the parking brakes. Chock the wheels on level ground and set the parking brakes once the brakes have cooled.
Texas CDL Handbook §5.4.8
Q11Inspection
You pull hard on a slack adjuster (wearing gloves). It probably needs adjustment if it moves more than about how far where the pushrod attaches?
- AAbout 1/8 inch
- BAbout 1 inch
- CAbout 3 inches
- DAbout 6 inches
Show answerHide answer
Answer B About 1 inch
More than about one inch of free movement means the brake probably needs adjusting. Too much slack can make a vehicle very hard to stop.
Texas CDL Handbook §5.3.2
Q12Inspection
In the applied leakage test, you shut off the engine, release the parking brake and the tractor protection valve, and hold the foot brake fully down for one minute. For a combination vehicle, the air loss is too much if pressure drops more than:
- A4 psi
- B10 psi
- C15 psi
- D20 psi
Show answerHide answer
Answer A 4 psi
With the foot brake held, a drop of more than 4 psi in a minute is too much for a combination vehicle (more than 3 psi for a single vehicle). Find and fix the leaks before driving.
Texas CDL Handbook §5.3.3
Q13Inspection
How do you test the low air pressure warning signal?
- ADrive at highway speed and brake hard several times in a row
- BOpen the safety relief valve by hand until the light comes on
- CEngine off, electrical power on, then fan the brake pedal to lower tank pressure
- DPull out the parking brake knob with the engine running fast
Show answerHide answer
Answer C Engine off, electrical power on, then fan the brake pedal to lower tank pressure
Fanning the brake lowers the tank pressure. The warning must come on before pressure drops below 55 psi (in the lowest tank, on a dual system).
Texas CDL Handbook §5.3.3
Q14Using air brakes
What is controlled braking?
- ABraking all the way, then releasing each time the wheels lock up
- BPumping the brake pedal quickly and lightly the whole time
- CBraking as hard as you can without locking the wheels, steering very little
- DSlowing down with only the parking brake control
Show answerHide answer
Answer C Braking as hard as you can without locking the wheels, steering very little
If you need to steer more or the wheels lock, release the brakes, then re-apply as soon as you can. Braking all the way and releasing each time the wheels lock is a different method, called stab braking.
Texas CDL Handbook §5.4.3
Q15Using air brakes
You are in the proper low gear on a long downgrade, and your safe speed is 40 mph. Using the braking method in the CDL manual, when do you release the brakes?
- AWhen your speed is down to about 20 mph
- BNever; hold light, steady pressure all the way down
- CAs soon as you feel the vehicle start to slow
- DWhen your speed is down to about 35 mph
Show answerHide answer
Answer D When your speed is down to about 35 mph
Brake hard enough to feel a definite slowdown until you are about 5 mph below your safe speed, which takes about three seconds. When you are back up to the safe speed, repeat.
Texas CDL Handbook §5.4.6
Q16Using air brakes
Which statement about antilock brakes (ABS) is correct?
- AIt always shortens your stopping distance on any surface
- BIt adds extra braking power to your normal brakes
- CIt helps you keep control, but may not shorten your stopping distance
- DIt works during every stop, even gentle ones
Show answerHide answer
Answer C It helps you keep control, but may not shorten your stopping distance
ABS works alongside your regular brakes and steps in only when a wheel is close to locking. It does not make your brakes stronger or weaker.
Texas CDL Handbook §5.1.16
Q17Low air & emergencies
The low air pressure warning comes on while you are driving. What should you do?
- AStop and safely park as soon as possible
- BKeep driving; the spring brakes will stop you if needed
- CPump the brake pedal to build pressure back up
- DSpeed up to reach a repair shop sooner
Show answerHide answer
Answer A Stop and safely park as soon as possible
There may be an air leak. You can only make a controlled stop while enough air remains in the tanks.
Texas CDL Handbook §5.4.7
Q18Low air & emergencies
Under the CDL manual, a visible low air pressure warning must come on before tank pressure falls below what level? (Some older vehicles use half the governor cut-out pressure instead.)
- A20 psi
- B55 psi
- C100 psi
- D125 psi
Show answerHide answer
Answer B 55 psi
The warning is usually a red light, and a buzzer may also sound. Bring the vehicle to a safe stop as soon as it comes on.
Texas CDL Handbook §5.1.11
Q19Low air & emergencies
Why is it safer to stop when the low-air warning comes on instead of waiting for the spring brakes to come on?
- AThe spring brakes will not come on at all if you wait
- BYou can still use the foot brake to control the stop
- CThe spring brakes only work on the trailer
- DWaiting raises the air pressure back to normal
Show answerHide answer
Answer B You can still use the foot brake to control the stop
Controlled braking is only possible while enough air remains. Once the spring brakes come on, the stop may be long or the vehicle may skid.
Texas CDL Handbook §5.4.7
Q20Brake adjustment
According to the CDL manual, what is the most common problem found in roadside inspections?
- ABrakes out of adjustment
- BEmpty alcohol evaporators
- CBroken stop light switches
- DMissing trailer ABS lamps
Show answerHide answer
Answer A Brakes out of adjustment
Out-of-adjustment brakes are the most common problem found at roadside inspections, and too much slack can make a vehicle very hard to stop. Check the slack adjusters.
Texas CDL Handbook §5.3.2
Q21Brake adjustment
On a brake with an automatic slack adjuster, the pushrod stroke is past the legal adjustment limit. What does that usually mean?
- AThe driver should re-adjust it by hand every day
- BA problem with the adjuster or other brake parts, or a bad installation
- CThe air pressure in the tanks is set too high
- DThe adjuster is working the way it was designed
Show answerHide answer
Answer B A problem with the adjuster or other brake parts, or a bad installation
Automatic adjusters should not normally need manual adjustment. A stroke over the limit points to a problem that needs repair.
Texas CDL Handbook §5.3.2
Q22Brake adjustment
How can brakes that are out of adjustment lead to brake fade?
- AThey make the governor cut out too early
- BThey cause the safety relief valve to open
- CThey lower the air pressure in the tanks
- DThey stop doing their share, so the other brakes overheat
Show answerHide answer
Answer D They stop doing their share, so the other brakes overheat
Every brake must do its share of the work. When some stop doing so, the rest take on extra load and can overheat.
Texas CDL Handbook §5.4.5
Q23Federal rules
Under federal CDL rules, what happens if you fail the air brake part of the knowledge test?
- AYour CLP or CDL, if issued, is restricted from operating a CMV with any type of air brakes
- BYou cannot be issued any CDL at all
- CYou may drive air-braked vehicles only within your home state
- DYou may drive air-braked vehicles only with another CDL holder on board
Show answerHide answer
Answer A Your CLP or CDL, if issued, is restricted from operating a CMV with any type of air brakes
Section 383.95 requires the state to mark an air brake restriction on the CLP or CDL. You can still get the license, but not drive CMVs with air brakes.
49 CFR 383.95
Q24Federal rules
You take the skills test in a vehicle with air-over-hydraulic brakes. Under federal rules, what restriction goes on your CDL?
- AYou are restricted from all vehicles with hydraulic brakes
- BYou are restricted from vehicles with any air brakes, including air-over-hydraulic
- CYou get no restriction at all
- DYou are restricted from CMVs with brakes that work fully on the air brake principle
Show answerHide answer
Answer D You are restricted from CMVs with brakes that work fully on the air brake principle
Testing in an air-over-hydraulic vehicle leads to the full air brake restriction under 383.95(b). You can drive air-over-hydraulic vehicles but not full air brake vehicles.
49 CFR 383.95
Q25Federal rules
Under 49 CFR 393.51(c), what must a commercial motor vehicle with air brakes be equipped with?
- AAn alcohol evaporator for cold weather
- BAn air pressure gauge and a warning signal
- CAutomatic air tank drain valves
- DA front brake limiting valve
Show answerHide answer
Answer B An air pressure gauge and a warning signal
Section 393.51(c) requires a pressure gauge and a warning signal on any CMV with air brakes (or towing a vehicle with air brakes), regardless of manufacture date. Paragraph (f) exempts only some small, older property-carrying vehicles.
49 CFR 393.51